12GA FH-- Hairy Blaster-- - Page 8 - Arms Locker
Arms Locker Gun Forum
Go Back   Arms Locker > Arms Locker > Gun Talk


Like Tree4Likes
Reply
 
LinkBack Thread Tools Display Modes
Old 03-12-2010, 09:35 PM   #141
Registered User
 
Joined: Jul 2008
From: Brinton, MI

Posts: 276
I get asked about presses used for big cases.
Here is a picture of my 2 big presses on
the heavy bench, with the case spinner/lathe
on the back of the bench. Blue one is a Walnut
Hill and the green is beefed up Ammomaster.
Both are braced so I can lean on them.Bench is
braced to wall supports and benches behind.

You can see the expanders laid out on the press
brace arms, and a whole bunch of shorty dies laid
out, that fit everything from 10ga down to
my 700HE. And variety of large cases and real large
4ga-8ga dies, parts I work with. On the right is a
stack of my 585HE dies in the die boxes.Ed

 
Remove Ads
Old 03-17-2010, 09:35 PM   #142
Registered User
 
Joined: Jul 2008
From: Brinton, MI

Posts: 276
Now might get real exciting load developement wise,
If we could make brass cases as long as the paper
one on the right. In picture is 3.5" 10ga plastic
case, our 10GA FH brass 4.05" case I made by putting
a 10ga basecup on 50cal Russian brass, and third
a 6" long 10ga bomb disposal case used to shoot
liquid/gel in to bomb packages, I think.
Anyone knows for sure let me know.ED

 
Old 03-23-2010, 10:46 PM   #143
Registered User
 
Joined: Jul 2008
From: Brinton, MI

Posts: 276
Here is picture showing surplus 50 Russian case before
and the 10ga brass case we make using it with
10ga bases pressed and epoxied on and expanding
case out straight, making the 4.050" long
10ga case.Makes a great 10ga FH.
And the case isn't weakened any, by the
process of putting on the rim.It will
stand any pressures any gun could...ED

 
 
Old 03-28-2010, 10:12 PM   #144
Registered User
 
Joined: Jul 2008
From: Brinton, MI

Posts: 276
We have put 4 different cartridges in the Savage 210
bolt gun. We added various 12ga and .700"
heavy thick barrels.
The first was our 12ga FH long case.
The second was my 700H 3.25" belted case.
Third was the 3.5" 12ga that Bret did, and
fourth is the 700NE that we wanted to see
how it works. It shoots fine, has weighted stock,
and a 27 inch barrel.Has a double thick pad.
I even have cast slugs for 700.
Cases are expensive, ones in picture are
20 bucks each...Ed

 
Old 04-02-2010, 11:06 PM   #145
Registered User
 
Joined: Jul 2008
From: Brinton, MI

Posts: 276
Here is picture of my Mossy 695 that has heavy barrel for
the our long 12ga cases, in fact it chambers the 12ga
belted shown in picture ok that I use for testing.
I set chamber to do belted as well as rimmed.

Second picture is some of my 585 Short HE cases, that work
great in regular length actions.We have these in Ruger,
Enfields, Mausers already. I have available supply of
brass for these of about 8-9000. Ed



 
Old 04-11-2010, 11:19 PM   #146
Registered User
 
Joined: Jul 2008
From: Brinton, MI

Posts: 276
Getting to some more 4ga/bore work.With barrel and
falling block action locked down fired off some blank
type loads to test the breach and firing pin I set up.
I fired it by hitting the back of firing pin with a rod,
as I now have get hammer and trigger setup. Firing pin
dents primers ok, breach works and headspace is ok.

For loads I have wads to take up space above powder.
Others with same 4ga case in doubles fill case about
1/6 full of Blue Dot (110gr), with 2000gr slug.

I'll use 1600 gr hollowbase slugs, with about 1/3 of a case
of IMR 4759 or 1/2 to 5/8 case of RE17, rest filled
with fiber wads.These are shotgun primer loads and I will be
using THE STRONGER PRIMERS OF KILN CASES at about same
price as BMG primers. And I have BMG primer cases also
that I will test also, once gun is finished in a few weeks.Ed
 
Old 04-21-2010, 10:17 PM   #147
Registered User
 
Joined: Jul 2008
From: Brinton, MI

Posts: 276
Fired 4bore with 760 gr light round ball with
fiber wads under it, using 150gr Blue Dot
and shotgun primer case. Just starting loads
for testing operation. Hardly no recoil,
like a heavy, beefed up blank load,
could go much higher with that light
of round ball. Will have pics of the muzzle
blast and the gun shooting from the side,
using heavier slugs in a week or so.
In Owen's 4bore double,that uses same case
size they use max of 110gr of Blue Dot
with 2000 gr slug. Ed

 
Old 04-24-2010, 09:44 PM   #148
Registered User
 
Joined: Jul 2008
From: Brinton, MI

Posts: 276
Fired the 4bore with the 760 gr round ball,
which is a hard rubber coated steel ball,
thus the light weight compared to lead,
using 100gr of Blue Dot under 300gr RE17,
total 400gr. Hairy load, with 3500 fps, and
20,000 ft lbs. Used the turned 4bore cases,
with shotgun primers, and with that light
projectile case doesn't need sizing. This is
good beginning bullet weight for early testing.
I am gonna do 1200gr and 1600gr holding the
speeds to give about same energy.
I won't load heavier until I get another
stock like one I have that is full width.
Also those who want 3.5" 20ga brass cases,
Rocky Mtn Cartridge is making them now.ED
 
Old 04-30-2010, 09:52 PM   #149
Registered User
 
Joined: Jul 2008
From: Brinton, MI

Posts: 276
Tested 4bore with a double ball load of 1250 grains weight,
Used 100gr Blue Dot under 250gr of RE17, with card and
one fiber wad. 2600 fps. Recoil not bad, just brisk.
Used turned brass cases with shotgun primer, and cases
still didn't expand base. just size top..
Running about 23-25,000 psi.
The light ball load in above post
about 16,000 psi.. Ed
 
Old 05-05-2010, 09:40 PM   #150
Registered User
 
Joined: Jul 2008
From: Brinton, MI

Posts: 276
Some interesting shooting with 4bore.

Double 760gr ball load of 1520 gr total, at 2300 fps.

A buck and ball load, 6 45cal lead balls, 133gr each,
and a 760 gr ball on top, 1560 gr total, at 2300 fps.

Both loads 100gr BlueDot under 225gr Re17, In the
turned brass cases, with shotgun primer.Recoil
manageable, and like a big push. The sound isn't
a boom like regular shotguns, but cracks loud
like big bore rifles,at least twice as as loud.Ed
 
Old 05-12-2010, 11:36 PM   #151
Registered User
 
Joined: Jul 2008
From: Brinton, MI

Posts: 276
I got my 20ga FH 3.5" brass cases from RMC.
The case capacity in water is 234 gr.
It holds 215 gr of dense ball powder to the
base of 490gr 20ga hard lead slugs I have.
These cases use a 209Mag shotgun primer, and
I have mouth ID set up for .620 slugs as the slugs
and sabots I have are that size. These cases will
work good out to 35,000 psi, without extreme
expansion or resizing problems. Load of slow powder
will get 490 gr to 2500 plus at 25-27,000 psi,
6800 ft lbs, using the 30" barrel I'm getting to
put on the FBW Model L falling block.
! also have a case of the 3.5" factory Hastings
SPW, locked on sabot, loaded rounds to use.Ed
 
Old 05-21-2010, 09:41 PM   #152
Registered User
 
Joined: Jul 2008
From: Brinton, MI

Posts: 276
Here is pic of the RMC brass 20ga 3.5" with
Hastings 3.5" factory plastic case loads,
and 20ga Hollywood dies. Also slugs, Dixie 490 gr,
Hastings SPW and 900gr jacketed in the one case.

Second pic is the FBW Model L setup that will have
20ga 3.5" chambered barrel in a second one. This 1st
one is in my 585HE.It is falling block in one piece
thumbhole stock, an idea I come up with on my
4bore falling block. Second Model L will be built same
in 3.5" 20ga. EDd



 
Old 05-24-2010, 09:17 PM   #153
Registered User
 
Joined: Jul 2008
From: Brinton, MI

Posts: 276
Transition, biggest to a smaller, in
putting falling block actions in one piece stocks.
First one was the 4bore, the big one in
picture and after it was done I got a FBW falling block
and soon figured out I could do the same with it.
It is chambered in my 585HE cartridge.
And it is pictured above with the cases.
I built the 4bore, from blocks of steel.
The FBW is the Model L, and I'm doing second one
in 3.5" 20ga, to use brass and plastic cases.
And maybe later on when I find extra 700 barrel
we'll do my long 700HE in FBW....Ed

 
Old 05-31-2010, 09:19 PM   #154
Registered User
 
Joined: Jul 2008
From: Brinton, MI

Posts: 276
Here is picture of FBW Model L in one piece stock,
compared to a FBW Model S in 2 piece stock.
Both are chambered in my 585HE.
These two plus the Wickcliff 76 and Ruger #1
will easily handle my 585HE with proper
weight and thick pads. These guns have
rimless extractors and my 585HE goes in and
out with least amount of metal removal from
the feed trough, with much more power.
The Model L will have a 3.5" chambered 20ga
barrel to use 3.5" MRC brass cases and
Hastings factory or reloaded plastic cases.Also
I'm working to put a Wickcliff in 1 piece stock.Ed

 
Old 06-03-2010, 09:41 PM   #155
Registered User
 
Joined: Jul 2008
From: Brinton, MI

Posts: 276
Here is picture of a bolt action a fella on Practical
Machinist built for an 8ga. 4 rear bolt lugs.Singleshot.
He used section of 20mm barrel for barrel.. Real nice.
Idea would do for 10 and 12ga also I think.
Has an aimpoint sight. Ed

 
Old 06-08-2010, 09:44 PM   #156
Registered User
 
Joined: Jul 2008
From: Brinton, MI

Posts: 276
Here is picture of the fella firing his bolt
action 8ga that he made. He uses the
super strong, heavy duty, plastic cases
like we are using in the ones we made by
boring out NEFs to 8ga.Ed

 
Old 06-15-2010, 10:25 PM   #157
Registered User
 
Joined: Jul 2008
From: Brinton, MI

Posts: 276
Some have asked if the guy who made above
bolt action 8ga does them for others, no he only
did one for himself, and isn't a manufacturer.

Here is picture of a cast .504" slug BPI 12ga sabot
a guy made a few for me and it has good accuracy with
our slower powder loads, with the sabot working ok.
Slug is 440 gr and hard alloy cast with decent
meplat for good penetration.But it isn't too blunt
so it has good longer range capabilities when you
get the speed behind it. Soon be the deer season and
guys are still hunting for their ideal 12ga sabot/slug
setup for loading their own.BPI is supposed to have
a new sabot this year..Ed

 
Old 06-23-2010, 09:43 AM   #158
Registered User
 
Joined: Jul 2008
From: Brinton, MI

Posts: 276
The .504" lead slug I show for using in 12ga sabots is
one cast for using in .500" cases like my 499HE, by
sizing it after casting. Tried it at the .504" diameter and
it works in the sabot also. So it does double duty,
unsized 12ga sabot, sized and lubed in .500" use.

Some like short cases in big calibers, and have put up
various ideas. First picture is 12ga brass cases, two
2" long and other 2.25". Cases made by shortening
our cases we made by putting rims on bmg brass.
These can be used in Savage 210 and feed from mag
box. Can use 2.5" Magtech brass shortened so case
and protruding slug will be 2.7" overall and feed from
magazines of Savage & Mossy bolt guns. With 2.25" case
you can get 600gr to 1800 at least.Ed

 
Old 07-01-2010, 10:56 PM   #159
Registered User
 
Joined: Jul 2008
From: Brinton, MI

Posts: 276
Have had a bunch of different guys shooting
the 4bore with light 11,000 ft lb loads.
All say it is a tremendous thrill.
Simply the greatest shooting ever.

So many have opinions on what is a real big bore.
I think really big starts at .585........
So in that vein I have made the 585 Hubel
Super Magnum, 585 HSE, giving a nod to necked
cases.Also can make the 620 HSE for 600 guys.
This is my only wildcat base case with a neck.
Base and rim are .750", shoulder is .720".
and case is 3.7" long. Power in the range of
14,000 to 17,000 ft lbs. Can be used single shot
in the PH, the Savage 210, the Enfield. Not for
mass production by me, cases too hard to make.
An experiment with necked cases.
Picture of the case later.Ed
 
Old 07-10-2010, 10:35 PM   #160
Registered User
 
Joined: Jul 2008
From: Brinton, MI

Posts: 276
20 gauge-- Fired factory 3.5" plastic cased Hastings 395 gr
locked on sabot slug in 20ga with 30 inch barrel and
got 1900 plus fps. Same sabot slug in RMC 3.5" brass case
with shotgun primer, got 2500 fps. Case bases didn't
expand. Load of 150gr RE17 slow enough getting to
peak pressures is easy on cases. Dies work with
both case types.Ed

 
Reply

  Arms Locker > Arms Locker > Gun Talk


Thread Tools
Display Modes






Powered by vBulletin 3.8.7
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
SEO by vBSEO 3.6.1
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright © 2003 - 2011 Arms Locker. All rights reserved.